DANFOSS MOTOR 80 CM3 CYL. SHAF
Hydrokit Part Number : MHR080A1AD
Discontinued product replaced by :
MOTOR OMR X 80 SHAFT 25MM DIA ( MHR080A1AX )
Technical information
DANFOSS OMR MEDIUM-SPEED MOTOR
- Built with check-valve
- Displacement: 80.3cc
- Shaft: Cylindrical, Ø25mm, parallel key A8x7x32, reinforced seal
- Flange: 2-hole, Ø82.55mm centring, Ø106.4mm bolt centring
- Ports: 1/2" BSP (A & B side) - 1/4" BSP (drain)
- Danfoss part no.: 151-0711
- Built with check-valve
- Displacement: 80.3cc
- Shaft: Cylindrical, Ø25mm, parallel key A8x7x32, reinforced seal
- Flange: 2-hole, Ø82.55mm centring, Ø106.4mm bolt centring
- Ports: 1/2" BSP (A & B side) - 1/4" BSP (drain)
- Danfoss part no.: 151-0711
The frictions are reduced to the minimum thanks to the gear rim bearing and to the effectiveness of the hydraulic greasing. It permits a long life and a better efficiency even under continuous high pressures. The gear rim with rollers is advised with very light oils and for systems that require numerous switches.
Speed : max 160 to 775 RPM according to the engine
Cubic capacity : 50 to 375 cm³/rev
Speed (rpm) |
Torque (Nm) |
||||||||||
Displacement (cm³) |
max continuous |
min |
max continuous |
start min |
max continuous power (kW) |
max continuous pressure drop (bar) |
max continuous oil flow (l/mn) |
max starting pressure (bar) |
max continuous inlet pressure (bar) |
Sauer Danfoss reference |
Hydrokit reference |
51,6 |
775 |
10 |
100 |
80 |
7 |
140 |
40 |
10 |
175 |
151.0710 |
MHR050A1AD |
80,3 |
750 |
10 |
195 |
150 |
12,5 |
175 |
60 |
10 |
175 |
151.0711 |
MHR080A1AD |
99,8 |
600 |
10 |
240 |
200 |
13 |
175 |
60 |
10 |
175 |
151.0712 |
MHR100A1AD |
125,7 |
175 |
9 |
300 |
250 |
12,5 |
175 |
60 |
9 |
175 |
151.0713 |
MHR125A1AD |
159,6 |
375 |
7 |
300 |
240 |
10 |
130 |
60 |
7 |
175 |
151.0714 |
MHR160A1AD |
199,8 |
300 |
5 |
300 |
260 |
8 |
110 |
60 |
5 |
175 |
151.0715 |
MHR200A1AD |
249,3 |
240 |
5 |
300 |
240 |
6 |
80 |
60 |
5 |
175 |
151.0716 |
MHR250A1AD |
315,7 |
190 |
5 |
300 |
260 |
5 |
70 |
60 |
5 |
175 |
151.0717 |
MHR315A1AD |
372,6 |
160 |
5 |
300 |
240 |
4 |
55 |
60 |
5 |
175 |
151.0718 |
MHR375A1AD |
Technical data
Motor type | OMR Geroller | ||
Displacement | 80 | cc/rev | |
Flange type | SAE A flange | ||
Shaft type | Cylindrical | ||
Size of the shaft | 25 mm | ||
Orifices position | Side port - Offset | ||
Orifices A & B size | G1/2 | ||
Taille du drain | G1/4 | ||
Shaft seal | Int. in shaft seal 225 bar | ||
Bearing type | Journal bearing | ||
Speed sensor | No | ||
Paint | Not paint | ||
Marque | Danfoss / White WDMS |